Reality Modified & Super Rules

 

 

 Reality Modified  2018-2019  Rules    Updated 3/13/19

                                      All teching will be done Pre Race w/cars impounded Mods & Supers

                    Format: 2-Mains each class. Points combined in each class tie breaker in 2nd Main fastest time

# 1. Body: Approved  asphalt type modified body. .  Bodies made by Reality Raceway , NY Modifieds , & Jer's bodies . No modifcations. 

All cars must have a Drivers Head and Air Cleaner/  Hood bubble.  It is intended that these cars look as realilistic as possible.  Also the intent is that the cars remain as  spec. cars  . All  bodies  must have  windshields and rear panels and must remain.   No air holes front or rear.  Rear panels on  all mods required.   Max. spoiler ht. is 5/16 " from interior deck panel. No Vanes. All Bodies will conform to the Reality body design Specs..(supplied)  Conventional

NEW  words to help discribe Rules ..Conventional = Meaning Conforms to the intent of the Rules. & Non-Conventional = does not comply with intent to conform .

    Straight wired controllers only. >>>Subject to Approval.<<<< Conventional Parma or Koford ONLY ..with Brake Adj. NO Electronic devices between track and controller handle.  ONLY External brake reostat  allowed.  

# 2. Chassis:  The New Reality Modified Chassis ..  PN: RMC-2016-18  , Parma FCR # 577 and K & G cut to pattern

                  NO PAINT or Tape on CHASSIS BOTTOM  that interfers with chassis gauge

   Front wheels may spin independently. Must have soild steel axles front and rear.   Minimum axle dia. 1/8 ".

 Oilites: May Be modified ..Oilites may be soldered/ glued in. Parma  # 626 offset or # 628 centered oilites ONLY... 

 NO Ball Bearings .  SPEC.  Guide flag   Parma # 645 ONLY  stock no modification                                                                                                                                                   

   All cars must have rear bumpers made from 1/8 - 3/16 " channel, square, or rectangular brass only. .

 Rear bumper Minimum ht. 5/16 " any part there of.  All cars must have full side bars, full  double rear side-bars as spec car sold,  1/16 " dia. max/ brass rod only.  Front bumper must attach to the chassis at 4 points.

  May be reinforced with piano wire.   All bars must be approved. See Tech Page.

   No chassis modifications/ alterations.      May be reinforced w/piano wire .   Motor bracing allowed.

   No drilling or lighten of chassis. Weight may be added. All weigh must be stationary   ... Minimum weight - 145 grms 

   Chassis Clearence is .047min.   

# 3. Spacers: The ONLY SPACERS that will be used are the the following SONIC spacer in their respective locations. Champion gauge does not apply                                                                      

Left Frt.- One- .060   # 18-.060- Both Chassis

Right Frt.- One- .160. Sonic spacer. Part # SON-. 18-160.    Parma- One- .160. Sonic spacer. Part # SON-. 18-160

Right Rear. One- .160. Sonic spacers. # SON- 18-.160.  Parma-  Two- .160. Sonic spacer. Part # SON-. 18-160

Left Rear. One- .060.  Sonic spacer. # SON-18-060.  Parma - One- .160. Sonic spacer. Part # SON-. 18-160

# 4. Tires: ALL Tires.. Pro-Trac Daytona Stockers ONLY.    Nail Polished allowed.  MUST have PRO-TRACK Lettering

    Front Tires MUST TOUCH TRACK

    Front and  Rear Tires.. ALL MUST BE Pro-Track .With the lettering in place.. STOCK WIDTH UN-CUT. . 

    FULL tire contact  patch required.  Minimum Dia. is .830 FRONT  & REAR  measured inside & outside.  >>> Pre Race. <<<             Maximum Dia. is .880.

# 5. Motors:  The motor allowed in these cars will be the  >> HAWK 7  PART # 30307 <<  With laser numbers 77777 

        NO Gauss      No Modifications. Any signs of altering will be instance disquailifcation.

# 6.  GEAR - any pinion .... 28-30t Crown gears  as Spec. No lightening/ altering   

# 7. Add ons >>> Sk Modifieds  Retro hawk 7 long shaft  Allowed..Open gear.  K& G Straight rail add:10 Grms

SuperModRules (jpg)

Download